Magnum79
QuadCab
Weiß jemand ob nur der Dodge Händler das Ding programmieren kann?
Hab mal was gehört das es bei Bosch oder so auch gehen soll......
Hab mal was gehört das es bei Bosch oder so auch gehen soll......
Schlüssel programmieren
- Ersteller Duke of Earl
- Erstellt am
Help Support Dodge-Forum:
Duke of Earl
QuadCab
soweit ich weiss, kann das nur der Freundliche. Müssen einen PIN beim programmieren eingeben, sonst geht´s nicht.
Hallo, hat die Radioumstellung hingehauen?
Duke of Earl
QuadCab
nein leider nicht. Ist nicht in das Radio gekommen, mit dem Star Scan.
Rik
1500s
Duke of Earl
QuadCab
War zwar nicht genau der Händler, aber Schlüssel sehen genauso aus.
Angepasst hats dann der Freundliche.
Wenn Du 2 funktionierende Schlüssel hast, dann kannst Du auch selber Programieren.
Ich hatte leider nur einen.
Angepasst hats dann der Freundliche.
Wenn Du 2 funktionierende Schlüssel hast, dann kannst Du auch selber Programieren.
Ich hatte leider nur einen.
Zuletzt bearbeitet von einem Moderator:
![BRILLIANT TOOLS BT641240 Doppelkupplungs-Werkzeug für Volvo, Ford, Chrysler und Dodge [Powered by KS TOOLS]](https://m.media-amazon.com/images/I/3196Pg-lV1L._SL500_.jpg)
Rik
1500s
Hatte auch gerade mal bei "Chrysler-Ostendorf" in Hamm angerufen:
Schlüssel pro Stk 100EUS +MwsT + anlernen (jeweils ca 15€)...
werde dann wohl in der amerikanischen Bucht bestellen und denen das anlernen überlassen...
Gruß
Ryck
Duke of Earl
QuadCab
Den Preis hatten die mir auch gesagt. Das war mir dann auch zu teuer. Mein Dodge Händler konnte sie aber nicht schleifen, also hab ich´s eben selber gemacht.
Rik
1500s
das schleifen denke ich bekomme ich beim Schlüsseldienst hin, habe um die Ecke nen wirklich guten... Sonst spreche ich Dich nochmal an
Rik
1500s
W
Wingfox
Guest
Bei den neueren Fahrzeugen geht das nur wenn der Dealer erstmal online geht, genau wie bei Mercedes, von denen kam das wohl zu Chrysler ....
Ich muesste hier ca. 180 Dollar fuer Schluessel und Programierung zahlen, mal sehen ob der Herr Kunde das will oder ob lieber spaeter mehr zahlt.
Ueberigens sind die Nummern auf den Gehaeusen der Schluessel wichtig, ich dachte ich haette die Dinger fuer die Haelfte aus e-bay kaufen koennen .......
Rik
1500s
wer weiß, wie ich einen 3. Schlüssel anlerne? Also vorausgesetzt, das ich 2 Schlüssel habe natürlich!
Dank im voraus!
Rik
Dank im voraus!
Rik
Duke of Earl
QuadCab
CUSTOMER LEARN METHOD
NOTE: The Customer Learn feature is only available on domestic vehicles, or those vehicles which have a U.S. country code designator. This programming method also requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, or if the vehicle does not have a U.S. country code designator, the Secured Access Method MUST be used to program new or additional valid keys to the SKIM.
The Customer Learn programming method procedures are as follows:
1. Obtain the blank Sentry Key(s) that are to be programmed as valid keys for the vehicle. Cut the blank key(s) to match the ignition switch lock cylinder mechanical key codes.
2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the On position.
3. After the ignition switch has been in the On position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the Off position. Replace the first valid Sentry Key in the ignition switch lock cylinder with the second valid Sentry Key and turn the ignition switch back to the On position. The second valid Sentry Key must be inserted in the lock cylinder within fifteen seconds of removing the first valid key.
4. About ten seconds after the completion of step 3, the security indicator in the instrument cluster will start to flash to indicate that the system has entered the Customer Learn programming mode.
5. Within sixty seconds of entering the Customer Learn programming mode, turn the ignition switch to the Off position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the On position.
6. About ten seconds after the completion of step 5, the security indicator will stop flashing, stay on solid for three seconds, then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKIS will immediately exit the Customer Learn programming mode. After the ignition is cycled the vehicle may be started using the newly programmed valid Sentry Key.
Each of these steps must be repeated and completed in their entirety for each additional Sentry Key that is to be programmed. If the above steps are not completed in the given sequence, or within the allotted time, the SKIM will exit the Customer Learn programming mode and the programming will be unsuccessful. The SKIM will also automatically exit the Customer Learn programming mode if it sees a non-blank Sentry Key transponder when it should see a blank, if it has already programmed eight (8) valid Sentry Keys, or if the ignition switch is turned to the Off position for more than about fifty seconds.
NOTE: If an attempt is made to start the vehicle while in the Customer Learn mode (security indicator flashing), the SKIS will respond as though the vehicle were being started with an invalid key. In other words, the engine will stall after about two seconds of operation. No faults will be set.
NOTE: Once a Sentry Key has been programmed as a valid key to a vehicle, it cannot be programmed as a valid key for use on any other vehicle.
NOTE: The Customer Learn feature is only available on domestic vehicles, or those vehicles which have a U.S. country code designator. This programming method also requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, or if the vehicle does not have a U.S. country code designator, the Secured Access Method MUST be used to program new or additional valid keys to the SKIM.
The Customer Learn programming method procedures are as follows:
1. Obtain the blank Sentry Key(s) that are to be programmed as valid keys for the vehicle. Cut the blank key(s) to match the ignition switch lock cylinder mechanical key codes.
2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the On position.
3. After the ignition switch has been in the On position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the Off position. Replace the first valid Sentry Key in the ignition switch lock cylinder with the second valid Sentry Key and turn the ignition switch back to the On position. The second valid Sentry Key must be inserted in the lock cylinder within fifteen seconds of removing the first valid key.
4. About ten seconds after the completion of step 3, the security indicator in the instrument cluster will start to flash to indicate that the system has entered the Customer Learn programming mode.
5. Within sixty seconds of entering the Customer Learn programming mode, turn the ignition switch to the Off position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the On position.
6. About ten seconds after the completion of step 5, the security indicator will stop flashing, stay on solid for three seconds, then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKIS will immediately exit the Customer Learn programming mode. After the ignition is cycled the vehicle may be started using the newly programmed valid Sentry Key.
Each of these steps must be repeated and completed in their entirety for each additional Sentry Key that is to be programmed. If the above steps are not completed in the given sequence, or within the allotted time, the SKIM will exit the Customer Learn programming mode and the programming will be unsuccessful. The SKIM will also automatically exit the Customer Learn programming mode if it sees a non-blank Sentry Key transponder when it should see a blank, if it has already programmed eight (8) valid Sentry Keys, or if the ignition switch is turned to the Off position for more than about fifty seconds.
NOTE: If an attempt is made to start the vehicle while in the Customer Learn mode (security indicator flashing), the SKIS will respond as though the vehicle were being started with an invalid key. In other words, the engine will stall after about two seconds of operation. No faults will be set.
NOTE: Once a Sentry Key has been programmed as a valid key to a vehicle, it cannot be programmed as a valid key for use on any other vehicle.
Rik
1500s
wo kriegst Du diese Infos denn her? Hätte ich das auch finden können??
DANKE!!
DANKE!!
Duke of Earl
QuadCab
Hab ich von einem US Forum. Hoffe es hilft
Rik
1500s
werde es mal probieren, zumindest dann wenn der Freundliche für den 3ten Schlüssel programmieren Geld haben will
Duke of Earl
QuadCab
2 Schlüssel programmieren hat mich ca. 17 Euro gekostet
Rik
1500s
aber nicht bei meinem Händler
Rik
1500s
nur nochmal eben um das Ergebniss mitzuteilen:
a) Schlüssel aus der USA-Bucht bestellt; Kosten für 2 Stück incl Versand: ca 30 Euro
b) Schlüssel bei einem fähigem Schlüsseldienst schleifen lassen; Kosten: ca 9 Euro für beide
c) beim Chrysler-Dealer anlernen lassen; Kosten für 10Arbeitswerte: ca 15 Euro (inklusive dem Versuch den Tacho zu justieren)
Wert eines vorrätigen Ersatzschlüssels: unbezahlbar :mrgreen:
Rohlingpreis bei Chrysler schwankt zwischen 130 & 250 Euro, alle Preise selber gehört...!
Gruß
Rik
Steht auch im Benutzerhandbuch ab Seite 11 :lol:
Falls du keins hast: https://www.dodge-forum.eu/viewtopic.php?f=42&t=6586
Offenbar sind diese integrierten Schlüssel "Sentry-Keys" aber noch was Anderes als simple Keyless-Entrys. Daher wohl die genannten Preisunterschiede. Ich habe grad die gewöhnlichen Remotes anfertigen lassen für 65,- Euro das Stück incl. Programmieren, das gehörte zum Service.
